Artesive Plain Series – LA-010 Light Pink Glossy

SKU: ART-LA-010 Category:

Da

Product available on request

This texture is available only upon request at the moment. It means that it is possible to send a request for the production of the indicated color but a confirmation from our part is necessary and there may be time and quantity constraints. Upon request, you will be contacted by our production department.

    Description

    Light Pink Glossy

    At the moment this model is available on request. Send your request for more information on the specific texture.

    Plain Glossy Series

    The Artesive Plain Series represents all solid models. This adhesive self-adhesive film made of PVC offers very special features, perfect to be used to coat surfaces such as wood, plastic, metal and smooth surfaces such as plasterboard or MDF. The choice of solid self-adhesive films are smooth, without streaks. The polished version is completely smooth.

    Quality and Easy Application

    Like all Artesive self-adhesive films, including this Plain series are conformable, in which heating them allows you to model and apply them easily in tricky areas such as edges or corners. The adhesive being used is not set immediately to 100%, but allows you to remove the film to be repositioned in the event of errors. Patterns and textures of the series of Plain Artesive are in line with the trends of furniture of the moment.

    See the diagram below for some of the performance normally required by an adhesive coating for interiors. On a scale of 0 to 100 where 100 is the highest score, you can figure out which model is suitable for your use.

    Performance Plain Lack Series

    20%
    60%
    80%
    80%
    100%
    10%
    30%
    70%

    Features Plain Lack Series

    Conformable

    With the change in temperature the film stretches and allows the installer to make it stick even in difficult spots such as corners or edges.

    Bubble Free System

    Thanks to the special composition and to the thickness of the upper, it is possible to drastically reduce the irritating air bubbles during the application.

    Unimmediate fixing

    The adhesive of Artesive vinyl films does not have the bite immediately to allow the immediate detachment and repositioning on the surface.

    The application of the film is usually done step by step. After taking the measurements, the necessary part is cut, leaving always a margin of tolerance. On the back of the film, a grid helps you make a precise and in-line cut.
    The film is repositionable at first, so do not be afraid to make mistakes. To help you first wet the surface to be treated with water, it will help you not to immediately attack the film.
    Once cut to size, the film is still placed with the protective sheet applied on the surface, stopping it with paper tape. Starting from one side only a small part of the adhesive protection is removed and glued to the surface.
    Any air bubbles can be removed with the help of a spatula. When the first piece of film is applied, the paper protection sheet is removed step by step.
    Do not remove everything, but one piece at a time, continuing to pass the spatula every time from the center to the outside removing air bubbles and any drops of water previously applied. When the application is complete remove the pieces of paper tape. Voilà, done!

    • If you need to make large surfaces, we suggest you to buy a small test roll, or a single roll, to verify that your imagination and color are exactly the ones you were looking for.
    • It is always better to apply the film lightly initially, to be sure of the correct positioning.
    • If you need larger films with larger sizes, you can contact us for a specific quote.

    • Materiale: PoliVinilCloruro (PVC)
    • Spessore: 220 μ ±10%
    • Margine di restringimento: 2% ca
    • Classe minima di reazione al Fuoco: NPD Materiale non ignifugo
    • Adatto Uso Interno: Sì
    • Adatto Uso Esterno: No
    • Riposizionabile: No
    • Adesivo: Permanente Acrilico
    • Resistenza Adesivo al Calore: 180°C
    • Metodo di Applicazione: a secco
    • Temperatura Ottimale di posa: 15/30°C
    • Materiale liner: Kraft spessore 120 μ±10%
    • Certificazione: UNI EN 12149:1999
    • Garanzia: 3 anni uso interno

    Download Data Sheet and Warranty

    Sign up to our newsletter

    To take advantage of promotions and exclusive offers! By subscribing you agree to our Terms, Privacy & Cookies Policy.