Artesive Wood Series – WL-020 Lacquered Bamboo

SKU: ART-LAC20 Category:

From

Product available on request

This texture is available only upon request at the moment. It means that it is possible to send a request for the production of the indicated color but a confirmation from our part is necessary and there may be time and quantity constraints. Upon request, you will be contacted by our production department.

    Description

    Lacquered Bamboo

    At the moment this model is available on request. Send your request for more information on the specific texture. The Bamboo Model has the same shade as the matt version but with a Polished and lacquered effect. It has grain in a vertical direction relative to the length of the coil.

    Glossy Wood Series

    The Artesive wood series is the perfect combination of materials, design and performance of application. This self-adhesive film made of PVC offers very special features, perfect to be used to coat surfaces such as wood, plastic, metal and smooth surfaces such as plasterboard or MDF. It’s surface has high thickness allowing a good feeling to the touch as well as sight. The Glossy Wood series has a completely smooth effect to the touch has an effect of lacquered wood.

    Quality and Easy Application

    Like all Artesive self-adhesive films, including this wood series, are conformable, in which heating them allows you to model and apply them easily in tricky areas such as edges or corners. The adhesive being used is not set immediately to 100%, but allows you to remove the film and reposition it in the event of errors. Patterns and textures Series of Wood Artesive are in line with the trends of furniture of the moment.

    See the diagram below for some of the performance normally required by an adhesive coating for interiors. On a scale of 0 to 100 where 100 is the highest score, you can figure out which model is suitable for your use.

    Performance Wood Lack Series

    20%
    60%
    80%
    80%
    100%
    10%
    30%
    70%

    Features Wood Lack Series

    Design

    Texture realistically similar to real wood. In the Lack version the veins are completely smooth and do not feel to the touch, to give a similar effect to the lacquering.

    Conformable

    With the change in temperature the film stretches and allows the installer to make it stick even in difficult spots such as corners or edges.

    Bubble Free System

    Thanks to the special composition and to the thickness of the upper, it is possible to drastically reduce the irritating air bubbles during the application.

    Unimmediate fixing

    The adhesive of Artesive vinyl films does not have the bite immediately to allow the immediate detachment and repositioning on the surface.

    The application of the film is usually done step by step. After taking the measurements, the necessary part is cut, leaving always a margin of tolerance. On the back of the film, a grid helps you make a precise and in-line cut.
    The film is repositionable at first, so do not be afraid to make mistakes. To help you first wet the surface to be treated with water, it will help you not to immediately attack the film.
    Once cut to size, the film is still placed with the protective sheet applied on the surface, stopping it with paper tape. Starting from one side only a small part of the adhesive protection is removed and glued to the surface.
    Any air bubbles can be removed with the help of a spatula. When the first piece of film is applied, the paper protection sheet is removed step by step.
    Do not remove everything, but one piece at a time, continuing to pass the spatula every time from the center to the outside removing air bubbles and any drops of water previously applied. When the application is complete remove the pieces of paper tape. Voilà, done!

    • If you need to make large surfaces, we suggest you to buy a small test roll, or a single roll, to verify that your imagination and color are exactly the ones you were looking for.
    • It is always better to apply the film lightly initially, to be sure of the correct positioning.
    • If you need larger films with larger sizes, you can contact us for a specific quote.

    • Material: Polyvinyl Chloride (PVC)
    • Thickness: 200 μm ±10%
    • Narrowing margin: 2% ca
    • Minimum class of reation to fire: NPD does not fireproof material
    • Product term applied inside: min 5 years
    • Product term applied to the outside: ND
    • Repositionnable: No
    • Adhesive: Permanent acrylic.
    • Heat resistance: 180 °C
    • Application method: dry
    • Optimal Application temperature: 15/30°C
    • Liner Material: Kraft thickness120 μm ±10%
    • Certification: UNI EN 12149:1999
    • Warranty: 3 years internal use only

    Download Data Sheet and Warranty

    Sign up to our newsletter

    To take advantage of promotions and exclusive offers! By subscribing you agree to our Terms, Privacy & Cookies Policy.