Artesive Tech Series – TEC-017 Satin Steel Matt
Free shipping for orders over 150 €
Prompt delivery, shipped within 24/48 hours
30 Days Easy Return
Satin Steel Matt
The Satin Steel model is part of the Tech Line. It has a design that incorporates the same texture of a steel sheet. The area is largely sensitive at touch with a slightly iridescent brushed effect. Mat finish.
Choose your Roll
Choose the width you need to minimize waste and facilitate application. You can choose between the various pre-cut rolls or the customized roll by indicating in the quantity field the exact meters required. This model is available in 4 different widths. 30 cm, 60 cm, 90 cm and 122 cm.
With the Tech Series, Artesive wanted to go beyond the concept of “self-adhesive film”. They are not just films, but true works of PVC. They have a thickness significantly greater than the other films, to enable a touch sensation never experienced before. They are perfect to create environments or unique details and are very modern. Perfect to use as decoration in interior spaces such as bathrooms or exclusive lounge space. But also to give an original touch to your home.
Quality and Easy Application
Like all Artesive self- adhesive films, including this Tech series are conformable, so you can shape the product by heating them for easy application in tricky areas such as edges or corners. The adhesive being used is not set immediately to 100%, but allows you to remove the film and reposition it in the event of errors.
See the diagram below for some of the performance normally required by an adhesive coating for interiors. On a scale of 0 to 100 where 100 is the highest score, you can figure out which model is suitable for your use.
Performance Tech Fantasy Series
Features Tech Fantasy Series
With the change in temperature the film stretches and allows the installer to make it stick even in difficult spots such as corners or edges.
Bubble Free System
Thanks to the special composition and to the thickness of the upper, it is possible to drastically reduce the irritating air bubbles during the application.
The adhesive of Artesive vinyl films does not have the bite immediately to allow the immediate detachment and repositioning on the surface.
|The application of the film is usually done step by step. After taking the measurements, the necessary part is cut, leaving always a margin of tolerance. On the back of the film, a grid helps you make a precise and in-line cut.|
|The film is repositionable at first, so do not be afraid to make mistakes. To help you first wet the surface to be treated with water, it will help you not to immediately attack the film.|
|Once cut to size, the film is still placed with the protective sheet applied on the surface, stopping it with paper tape. Starting from one side only a small part of the adhesive protection is removed and glued to the surface.|
|Any air bubbles can be removed with the help of a spatula. When the first piece of film is applied, the paper protection sheet is removed step by step.|
|Do not remove everything, but one piece at a time, continuing to pass the spatula every time from the center to the outside removing air bubbles and any drops of water previously applied. When the application is complete remove the pieces of paper tape. Voilà, done!|
- If you need to make large surfaces, we suggest you to buy a small test roll, or a single roll, to verify that your imagination and color are exactly the ones you were looking for.
- It is always better to apply the film lightly initially, to be sure of the correct positioning.
- If you need larger films with larger sizes, you can contact us for a specific quote.
- Material: Polyvinyl Chloride (PVC)
- Thickness: 220 μm ± 10%
- Shrinkage margin: approx. 2%
- Minimum reaction class to Fire: NPD Non-fireproof material
- Suitable Indoor Use: Yes
- Suitable for Outdoor Use: No
- Repositionable: No
- Adhesive: Permanent Acrylic
- Adhesive Heat Resistance: 180 ° C
- Method of Application: dry
- Optimal installation temperature: 15/30 ° C
- Liner material: Kraft thickness 120 μm ± 10%
- Certification: UNI EN 12149: 1999
- Warranty: 3 years internal use