Artesive Serie Tech – TEC-011 Dark Wood 3D Cubik

SKU: ART-TEC-011 Category:

From

Product available on request

This texture is available only upon request at the moment. It means that it is possible to send a request for the production of the indicated color but a confirmation from our part is necessary and there may be time and quantity constraints. Upon request, you will be contacted by our production department.

    Description

    Dark Wood 3D Cubik

    At the moment this model is available on request. Send your request for more information on the specific texture. The 3D Cubik model is divided into small pieces of cubic coloured wood with a three-dimensional effect . Horizontally they give the impression of being a real wooden wall, where the pieces seem to be in contrast. They are smooth to the touch and you cannot feel the grain, because this would decrease the 3D effect .

    Tech Series

    With the Tech Series, Artesive wanted to go beyond the concept of “self-adhesive film”. They are not just films, but true works of PVC. They have a thickness significantly greater than the other films, to enable a touch sensation never experienced before. They are perfect to create environments or unique details and are very modern. Perfect to use as decoration in interior spaces such as bathrooms or exclusive lounge space. But also to give an original touch to your home.

    Quality and Easy Application

    Like all Artesive self- adhesive films, including this Tech series are conformable, so you can shape the product by heating them for easy application in tricky areas such as edges or corners. The adhesive being used is not set immediately to 100%, but allows you to remove the film and reposition it in the event of errors.

    See the diagram below for some of the performance normally required by an adhesive coating for interiors. On a scale of 0 to 100 where 100 is the highest score, you can figure out which model is suitable for your use.

    Performance Tech Fantasy Series

    80%
    50%
    60%
    80%
    100%
    30%
    30%
    70%

    Features Tech Fantasy Series

    Conformable

    With the change in temperature the film stretches and allows the installer to make it stick even in difficult spots such as corners or edges.

    Bubble Free System

    Thanks to the special composition and to the thickness of the upper, it is possible to drastically reduce the irritating air bubbles during the application.

    Unimmediate fixing

    The adhesive of Artesive vinyl films does not have the bite immediately to allow the immediate detachment and repositioning on the surface.

    The application of the film is usually done step by step. After taking the measurements, the necessary part is cut, leaving always a margin of tolerance. On the back of the film, a grid helps you make a precise and in-line cut.
    The film is repositionable at first, so do not be afraid to make mistakes. To help you first wet the surface to be treated with water, it will help you not to immediately attack the film.
    Once cut to size, the film is still placed with the protective sheet applied on the surface, stopping it with paper tape. Starting from one side only a small part of the adhesive protection is removed and glued to the surface.
    Any air bubbles can be removed with the help of a spatula. When the first piece of film is applied, the paper protection sheet is removed step by step.
    Do not remove everything, but one piece at a time, continuing to pass the spatula every time from the center to the outside removing air bubbles and any drops of water previously applied. When the application is complete remove the pieces of paper tape. Voilà, done!

    • If you need to make large surfaces, we suggest you to buy a small test roll, or a single roll, to verify that your imagination and color are exactly the ones you were looking for.
    • It is always better to apply the film lightly initially, to be sure of the correct positioning.
    • If you need larger films with larger sizes, you can contact us for a specific quote.

    • Material: Polyvinyl Chloride (PVC)
    • Thickness: 220 μm ± 10%
    • Shrinkage margin: approx. 2%
    • Minimum reaction class to Fire: NPD Non-fireproof material
    • Suitable Indoor Use: Yes
    • Suitable for Outdoor Use: No
    • Repositionable: No
    • Adhesive: Permanent Acrylic
    • Adhesive Heat Resistance: 180 ° C
    • Method of Application: dry
    • Optimal installation temperature: 15/30 ° C
    • Liner material: Kraft thickness 120 μm ± 10%
    • Certification: UNI EN 12149: 1999
    • Warranty: 3 years internal use

    Download Data Sheet and Warranty

    Sign up to our newsletter

    To take advantage of promotions and exclusive offers! By subscribing you agree to our Terms, Privacy & Cookies Policy.