Artesive Stone Series – ST-08 Travertine Matt

SKU: ART-ST-08 Category:

From
3.99

How to order your adhesive film?

Quantity:
Free shipping for orders over 200 €
Prompt delivery, shipped within 24/48 hours
30 Days Easy Return
Do you need free samples to check the color? Click here

Description

Travertine Matt

The Travertino model is the perfect reproduction of real marble. It has a warm color that incorporates beige tones with contrasting brown veins. The surface is rough to the touch to simulate the feel of the real material. It can be used in both classic and modern environments. Being a marble effect, the veins do not have a single direction, so the film can be applied in both directions.

 

Choose your Roll

Choose the width you need to minimize waste and facilitate application. You can choose between the various pre-cut rolls or the customized roll by indicating in the quantity field the exact meters required. This model is available in 4 different widths. 30 cm, 60 cm, 90 cm and 122 cm.

Stone Series

The Artesive Stone series is dedicated to the self-adhesive films like stone. It is the perfect combination of materials, design and performance of application. This self-adhesive film is made of PVC which offers very special features, perfect to be used to coat surfaces such as wood, plastic, metal and smooth surfaces such as plasterboard or MDF.

Quality and Easy Application

Like all Artesive self-adhesive films, including this Stone series are conformable, in which heating them allows you to model and apply them easily in tricky areas such as edges or corners. The adhesive being used is not set immediately to 100%, but allows you to remove the film to be repositioned in the event of errors. The patterns and textures of the Artesive Stone series is in line with the trends of furniture of the moment.

See the diagram below for some of the performance normally required by an adhesive coating for interiors. On a scale of 0 to 100 where 100 is the highest score, you can figure out which model is suitable for your use.

Performance Stone Series

20%
60%
80%
80%
100%
30%
30%
70%

Features Stone Series

Conformable

With the change in temperature the film stretches and allows the installer to make it stick even in difficult spots such as corners or edges.

Bubble Free System

Thanks to the special composition and to the thickness of the upper, it is possible to drastically reduce the irritating air bubbles during the application.

Unimmediate fixing

The adhesive of Artesive vinyl films does not have the bite immediately to allow the immediate detachment and repositioning on the surface.

The application of the film is usually done step by step. After taking the measurements, the necessary part is cut, leaving always a margin of tolerance. On the back of the film, a grid helps you make a precise and in-line cut.
The film is repositionable at first, so do not be afraid to make mistakes. To help you first wet the surface to be treated with water, it will help you not to immediately attack the film.
Once cut to size, the film is still placed with the protective sheet applied on the surface, stopping it with paper tape. Starting from one side only a small part of the adhesive protection is removed and glued to the surface.
Any air bubbles can be removed with the help of a spatula. When the first piece of film is applied, the paper protection sheet is removed step by step.
Do not remove everything, but one piece at a time, continuing to pass the spatula every time from the center to the outside removing air bubbles and any drops of water previously applied. When the application is complete remove the pieces of paper tape. Voilà, done!

  • If you need to make large surfaces, we suggest you to buy a small test roll, or a single roll, to verify that your imagination and color are exactly the ones you were looking for.
  • It is always better to apply the film lightly initially, to be sure of the correct positioning.
  • If you need larger films with larger sizes, you can contact us for a specific quote.

  • Material: Polypropylene (PVC)
  • Thickness: 220 μ ± 10%
  • Shrinkage margin: 2% approx
  • Minimum fire reaction class: NPD Non-flame retardant material
  • Suitable for internal use: Yes
  • Suitable for outdoor use: No
  • Repositional: No
  • Adhesive: Permanent Acrylic
  • Heat Adhesive Resistance: 180 ° C
  • Application Method: dry
  • Optimal setting temperature: 15/30 ° C
  • Liner material: Kraft thickness 120 μ ± 10%
  • Certification: UNI EN 12149: 1999
  • Warranty: 3 years internal use

Download Data Sheet and Warranty

Sign up to our newsletter

To take advantage of promotions and exclusive offers! By subscribing you agree to our Terms, Privacy & Cookies Policy.